I-CO2 vs I-Diode Laser ye-Acrylic: Ngaba i-Diode Laser ingayinqumla i-Acrylic?
Indlela iDiode kunye neCO2 Lasers ezisebenza ngayo ngokwenene ekusikeni iAcrylic
Ileyiza yediode:Ukukhanya okuluhlaza okwesibhakabhaka okuyi-445nm. Kudlula ngqo kwizinto ezibonakalayo. Yimibala emnyama kuphela eyifunxayo, nto leyo edala ubushushu bokusikwa okanye ukukrolwa.
Ileyiza ye-CO2:Ukukhanya kwe-infrared okukude kwe-10.6μm. Phantse zonke iintlobo ze-acrylic — ecacileyo, enemibala, emhlophe — ziyayifunxa. Oko kukunika ukusika okuzinzileyo kunye nemiphetho ecocekileyo.
Okukwintsusa:Ukuba i-acrylic "iyayifunxa" i-laser kugqitywa bubungakanani bobude bayo, kungekuphela nje ngamandla.
Ngaba i-Diode Laser ingasika i-Acrylic ngokwenene?
Ewe, kodwa zonke ezi meko zintathu zingezantsi kufuneka zifezekiswe. Ungayiphosi nayiphi na — kwaye ayizukusebenza.
| Iyasebenza ✅ | AYISEBENZI ❌ |
|---|---|
| Mnyama | Ecacileyo |
| Ubhlu omnyama | Mhlophe |
| Ubomvu obumnyama | Imibala ekhanyayo / epinki |
| Uluhlaza obumnyama | Igqabile ekhanyayo |
| Omhlophe ocacileyo (ongacacanga) | I-Fluorescent |
| Amandla eDiode | Ubukhulu bokusika obunokuthenjwa obuphezulu |
|---|---|
| 5W | 2–3mm |
| 10W | 3–4mm |
| 20W | 4–5mm |
| 40W | 5–6mm |
| Uthelekiso | I-Diode Laser | I-CO2 Laser |
|---|---|---|
| Isantya sokusika | Icotha (100–150 mm/min) | Isantya (500–2000 mm/min) |
| Ukugqitywa komphetho | I-Matte / iqandisiwe | Ingakhanyiswa ngelangatye (icacile) |
| Imveliso yeqela | Ayisebenzi | Isebenza kakuhle kakhulu |
Ngoobani Abafanelekela Ukusikwa Kwelaser Yediode Ne-CO2 Laser Cutting?
Ngubani ofanelekileyo kwiDiode Laser?
Isivakalisi esinye:I-diode laser ifanelekile kubantu abathanda izinto abazithandayo, abenzi be-DIY, kunye neeworkshop ezincinci ezisebenzisa uhlahlo-lwabiwo mali oluncinci abasika i-acrylic emnyama/emnyama kuphela ukuya kuthi ga kwi-5mm ubukhulu kwaye abadingi i-acrylic ecacileyo, imveliso ekhawulezayo, okanye imiphetho ekhazimlisiweyo.
Imeko ezinokusingathwa yiDiode Laser
- Iitshixo ze-acrylic ezimnyama, iibheji, iipleyiti zamagama
- Izitendi zefowuni, iiphazili, imihombiso yedesika encinci
- Iziseko zemodeli, iiphaneli ze-elektroniki ezivalekileyo
- Ukukrola ifoto ngokuchanekileyo (i-diode eneneni inobukhulu obuncinci bebala kune-CO2)
Ngubani ofanelekileyo kwi-CO2 Laser?
Isivakalisi esinye:I-laser ye-CO2 ifanelekile kumashishini, abavelisi beebhetshi, kunye naye nabani na ofuna ukusika naluphi na uhlobo lwe-acrylic — ecacileyo, emnyama, emhlophe, okanye enemibala — kwiishiti ezityebileyo (ukuya kuthi ga kwi-20mm+), ngesantya esiphezulu, enemiphetho ecocekileyo nekhazimlisiweyo.
Imeko ezinokusingathwa yi-CO2 Laser
- Iimpawu ze-LED ze-acrylic ezicacileyo, iiphaneli zesikhokelo sokukhanya, oonobumba bekristale
- Iimpawu ezikhanyisiweyo, izitendi zokubonisa
- I-acrylic etyebileyo (>6mm)
- Yonke imibala ye-acrylic (mnyama, omhlophe, ocacileyo, onemibala)
I-CO2 Laser vs I-Diode Laser ye-Acrylic
| Uthelekiso | I-Diode Laser | I-CO2 Laser |
|---|---|---|
| I-acrylic ecacileyo | ❌ Hayi | ✅ Ewe |
| I-acrylic emnyama | ✅ Ewe (kancinci) | ✅ Ewe (ngokukhawuleza) |
| Ubukhulu obukhulu bokusika | ≤6–8mm | ≤20mm+ |
| Isantya sokusika | Icotha | Isantya esiphindwe ka-5–10 |
| Umgangatho womda | Yamkelekile, ayikhazimliswanga | Ingakhazimliswa ngamalangatye |
| Iinkcukacha zomzobo | Ngaphezulu (ubukhulu bendawo encinci) | Kulungile |
| Ixabiso lezixhobo | Iphantsi | Phezulu |
| Iindleko zokulungisa | Iphantsi | Iphakathi (izipili, ubomi beetyhubhu) |
Okukwintsusa:I-laser ye-diode ingasika i-acrylic emnyama kuphela - ayisebenzi kwimibala ecacileyo, emhlophe, okanye ekhanyayo. Icotha, inqunyelwe kubukhulu obuyi-≤6–8mm, kwaye ishiya imiphetho engacacanga kuphela. I-laser ye-CO2 isika yonke uhlobo lwe-acrylic (ecacileyo, emnyama, emhlophe, enemibala) ngesantya esiphindwe ka-5–10, iphatha ubukhulu obuyi-20mm+, kwaye inika imiphetho ecocekileyo ekhazimlayo.
Indlela Yokuseta Amandla e-CO2 Laser Ngokusekelwe kuBukhulu be-Acrylic
| Ubukhulu be-Acrylic | Amandla Acetyiswayo | Isantya Esicetyiswayo (mm/s) | Iipasi | Amanqaku |
|---|---|---|---|---|
| 5–8mm | 100W | 20–35 | 1 | Imiphetho ecocekileyo, ingaba sobala |
| 10mm | 100–120W | 12–20 | 1 | Uncedo lomoya luyafuneka |
| 15mm | 120–150W | 8–15 | 1–2 | Sebenzisa ilensi yokugxila |
| 20mm | 150–200W | 5–10 | 1–2 | Ukukhupha umoya ngamandla + ukupholisa amanzi kuyadingeka |
| 25mm | 200–300W | 3–6 | 2–3 | Inzuzo yetyhubhu yamandla aphezulu |
| 30mm+ | 300–500W | 2–4 | 2–4 | Ukusika ubukhulu obugqithisileyo |
Umatshini wethu wokusika we-Acrylic 130 unokusika amaphepha e-acrylic angama-21mm. Cofa ukuze ubone uvavanyo lwethu lwezinto.
Ukuba kufuneka usebenzise i-Diode Laser ukuze usike i-Acrylic, sebenzisa ezi Parameters
| Amandla eDiode | Ubukhulu obukhulu | Isantya Esicetyiswayo (mm/min) | Iipasi |
|---|---|---|---|
| 5W | 2–3mm | 80–120 | 2–3 |
| 10W | 3–5mm | 100–150 | 1–2 |
| 20W | 4–6mm | 150–250 | 1 |
| 40W | 6–8mm | 200–300 | 1 |
Ezona ziCutter zeLaser ziBalaseleyo zeAcrylic
| Inzuzo | Inkcazo |
|---|---|
| Amandla aphezulu (ukuya kuthi ga kwi-300W) | Ingasika i-acrylic etyebileyo kakhulu, yandise ukuhlukahluka kwemveliso |
| Uyilo lokudlula ngeendlela ezimbini | Ivumela izinto ukuba zibe banzi kunebhedi yokusikela — ilungele amaphepha amade e-acrylic |
| Iinketho ezininzi zomthombo we-laser | Ityhubhu yeglasi ye-CO2 (engabizi kakhulu) okanye ityhubhu yesinyithi ye-RF (ihlala ixesha elide, umgangatho ongcono wemitha) |
| Amashishini afanelekileyo | Iimpawu zevenkile yokuthengisa, izibiyeli zetumente, imiboniso yentengiso emincinci ukuya kwephakathi |
| Inzuzo | Inkcazo |
|---|---|
| Yenzelwe iibhodi ezinkulu ze-acrylic kunye nemisebenzi yobugcisa emikhulu yomthi | Ipasi enye, ishiti enkulu |
| Indlela yokugqitha ngeendlela ezine | Iphatha amaphepha amade kakhulu ngokuguquguquka okuphezulu |
| Ukusika ngesantya esiphezulu (36,000 mm/min) | Inzuzo enkulu yokusebenza kakuhle |
| Amashishini afanelekileyo | Imiboniso yentengiso yemveliso enkulu / yebhetshi, imiqondiso yenkampani, ifenitshala yanamhlanje |
Nantsi ividiyo yokusebenza malunga nokusika i-acrylic ecacileyo nge-CO₂ laser. Landela ukuze ufunde okungakumbi ngale nkqubo.
Ngowuphi kwaba matshini bababini ofanelekileyo kuwe? Nxibelelana nathi ukuze ufumane ulwazi, kwaye siya kukunika ingcebiso engcono.
FAQ
A: Ngokwesiqhelo hayi, okanye kakubi kakhulu.I-acrylic emhlophe ibonakalisa kwaye isasaza ubude be-wavelength eluhlaza okwesibhakabhaka (~445nm) ye-diode laser, ngoko ke amandla amancinci kakhulu afunxwayo. I-20W diode laser inokumakisha okanye inyibilikise umphezulu kancinci, kodwa ayiyi kunqumla. Ukuba kufuneka usebenzise i-diode laser kwi-acrylic, namathela kuyoimibala emnyama (mnyama, luhlaza okwesibhakabhaka, bomvu), sebenzisa isantya esicothayo, kunye nokupasa izihlandlo ezininzi — kodwa umgangatho we-edge usaya kuba ngaphantsi kakhulu kweziphumo ze-CO2.
A:Ewe.kwi-acrylic emnyama eyi-3–5mm.
A:I-diode (ubukhulu obuncinci bebala).
A: Ewe, kwaye ilungile kakhulu kuyo.Iilaser zeCO2 zezona zikhethwayo eziqhelekileyo zokusika i-acrylic — zombini ezikhanyayo nezinemibala, ezenziwe ngesinyithi okanye ezikhutshiweyo. Ngokuxhomekeke kumandla elaser, ungasika ubukhulu ukuya kuthi ga kwi-10–20mm. Umphetho osikiweyo udla ngokuba nokugqitywa okukhazimlisiweyo nokugudileyo. Qinisekisa nje ukuba umoya ungena kakuhle, njengoko i-acrylic enyibilikayo ikhupha umphunga omncinci ocaphukisayo.
Ukuba unemibuzo malunga nokusika amaphepha e-acrylic nge-laser ye-CO₂, nxibelelana nathi.
Ixesha lokuthumela: Juni-01-2026